PLI MPS-240, MPS-03 MEMOLUB HPS 3-OUTLET MULTI-POINT LUBRICATOR SYSTEM NOS!!

Description

PLI MPS-240, MPS-03 MEMOLUB HPS 3-OUTLET MULTI-POINT LUBRICATOR SYSTEM NOS!!
*******************************************  FREE SHIPPING!!  *************************************************
New Old Stock (NOS).  These were ordered in bulk as replacement units and shipped in one box therefore they will not be shipped in the original box.  Comes complete with instructions.
We also have a new "partial" unit (missing only the "memo") if you are interested in that unit just let us know and we will list.
Made by Power Lube Industrial (PLI) this is the Mega Size, 240 cc's of lubricant (standard size 120 cc's).  This is filled with Shell Gadus S2V220 2 grease lubricant (NLGI-2 High temperature).  If this is not the type of grease you need a grease refill kit is reasonably priced with many grease options or if a special grease is required PLI can provide a special order.
This is a 3 outlet model, can easily be changed to a 6 outlet by replacing the plugs with outlet fittings or reduce the number of outlets by installing plugs.  The outlets are 5/16" OD, tubing is sold separately and not included (precharging tubing with grease is required prior to installation).  Nylon tubing is recommended.  This is the HPS (High Pressure System) which can develop 350 PSI.  Comes as shown with the mounting plate.
This listing is for ONE (1)
PLI MPS-240, MPS-03 MEMOLUB HPS 3-OUTLET MULTI-POINT LUBRICATOR SYSTEM.
Thanks for looking!!
From the manufacturer:
MEMOLUB® HPS
General Description:
The MEMOLUB® HPS is a reusable, battery powered, electro-mechanical lubricator. It's
constant 350psi lubricant output pressure allows the unit to be direct mounted, remote
mounted up to 40 feet* away from the lube point, or coupled with a progressive distribution block to lubricate from 2 to 12 lube points. It is available in three capacity sizes 120cc, 240cc and 480cc. This model is self-contained, no external wiring required and can be used plant wide on a variety of applications.
Operation
The MEMOLUB® HPS metered positive displacement pump has been primed before shipment and is ready for use. On first installation, all fittings, lube lines and bearings should be pre-charged with the same lubricant that was ordered with the MEMOLUB® HPS lubricator. Next, program the MEMO system to the appropriate output rate for your application. Screw the MEMOLUB® HPS on the MEMO fitting. The HPS unit will cycle once and proceed to follow the program setting. Periodic visual inspection is recommended for all MEMOLUB® lubricators.
When the lubricant cartridge is empty, unscrew the MEMOLUB® HPS lubricator from the MEMO fitting. Place the unit on a firm surface, outlet end down. Push down on the clear plastic housing while turning the black plastic locking ring counter-clockwise. The housing and spring assembly will separate from the pump base. Remove the empty cartridge and battery pack and replace with a new one.
Benefits
Programming the HPS
The MEMOLUB® HPS daily lubricant output is programmed using the simple MEMO system. The Red, White and Black timing rings determine how often the lubricator will cycle. The seven basic time settings required to handle most applications are programmed by using one, two or all three colored timing rings. To fine tune the lubricant output, you can adjust the piston stroke by installing the spacer washers into the MEMO fitting yielding 52 output settings. Once set and installed, the program is retained in the MEMO fitting allowing the user to install a different MEMOLUB® HPS lubricator without having to reprogram the unit.
Reduce production downtime by lubricating your equipment while in operation Improve safety by remote
mounting the lubricator up to 40 feet from the lube point from hazardous locations.  Easily integrates with your current lubrication program.  Reduce lubrication costs by utilizing “Minimal Lubrication Practices”
*Maximum lube line length is dependent on ambient temperature, grease type and application back pressure.  A full featured battery powered, self-contained automatic lubricator that provides precise, reliable lubrication.
The MEMOLUB® HPS lubricator automatically delivers a small, precise amount of lubricant at regular intervals for an continuous supply of fresh lubricant directly to your lube point. Prevents over and under lubrication problems related to manual lubrication.
120, 240 or 480cc lubricant capacity 350psi max output pressure from start to finish
Use with Oil or Grease (up to NLGI #2)
Remote mount up to 40 feet from the lube point
Use in a wide temperature range of applications
All MEMOLUB HPS models use the same motor base assembly, making it easy to convert from one lubricant capacity to another by simply purchasing a low cost transparent housing kit.
Specifications
Operation: Electro-Mechanical, positive displacement pump
Lubricant cartridge capacity: 120cc, 240cc or 480cc (Replaceable)
Compatible lubricants: Oil or Grease (to NLGI #2)
Connection thread: 1/4" NPT Male Max operating pressure: 350psi (25 bar)
Temperature range: 5°F to 120°F (-15°C to 50°C)
Output timing settings: 52 Adjustable settings
Power supply: 4.5VDC Alkaline battery pack
External On/Off Control No
Remote installation: Up to 40 feet (12 meters), single-point*
Reusable: Yes
Multi-Point compatible: Yes